FroboBox:Armadillo
The first FroboBox version built for Armadillo I
Documentation
Diagram
Component list
| Motherboard | VersaLogic EBX27 Mamba EBX-formfactor single board computer with PCI104 carrier/connector. Intel Core2 Duo 2.0Ghz. 2GB DDR2 RAM. | VersaLogic |
| Harddrive | Intel 40GB SSD SATA | Dustin |
| CAN adaptor | Advantech PCM3680 PC/104 2-port CAN module | Tri-m |
| Power supply | M4-ATX, 250w output, 6v to 30v wide input Intelligent Automotive DC-DC Car PC Power Supply | Mini-Box |
| Ethernet/WiFi | Netgear MBR624GU | Netgear |
| Enclosure | ALUMINIUM 230X330X180MM | Farnell |
| Display | Suggestion… | RS |
| 8-pin connector | M12 a coded Female for (5)+(8)+(9)+(10)+(11) | Phoenix |
| 8-pin connector | M12 a coded Female for 1) | Phoenix |
| 5-pin connector | M12 a coded Female for (6)+(7) | Phoenix |
| 4-pin connector | M12 a coded Female for 2)+3)+4) | Phoenix |
| USB connector | USB Buccaneer panel for (12)+(14) | RS |
| Sealing cap | panel sealing cap for (12)+(14) | RS |
Connector description
The connectors used at the FroboBox is the industrial connector standard M12
RS232 (M12 a-coded - 8pins female connector)
(8)+(9) on block diagram.
There are no configuration jumpers for COM1 and COM2 since they only operate in RS-232 mode.
RS232/422/485 (M12 a-coded - 8pins female connector)
(10)+(11) on block diagram.
Use CMOS Setup on the Versalogic mainboard to select between RS-232 4-wire, RS-422, and RS485 operating modes for COM3 and COM4. Jumper block V3 (see datasheet MEBX37-1.pdf for description) is used to enable the RS-422/485 termination resistor for COM3 and COM4. Jumper V3[1-2] enables the RS-422/485 termination resistor for COM3, and jumper V3[3-4] for COM4. The termination resistor should be enabled for RS-422 and the RS-485 endpoint station. It should be disabled for RS-232 and the RS-485 intermediate station.
Analog Inputs (M12 a-coded - 8pins female connector)
(5) on block diagram.
Four analog to digital converters are available on the motherboard
CAN (M12 a-coded - 8pins female connector - based on CANopen)
(6)+(7) on block diagram These ports utilizes a 5-Pin M12 CANopen shown below.
ETHERNET 10/100 (M12 d-coded - 4 pins female connector)
(1)+(2)+(3) on block diagram.
GIGABIT ETHERNET (M12 d-coded - 8 pins female connector)
(4) on block diagram.
POWER CONNECTOR
1: GND (black), 2:GND(blue), 3:VCC(brown),4:VCC(White)
Scaffold
The internal scaffold for the FroboBox consists of three aluminum plates separated by 35 mm spacers. The lower plate is cut in shape to fit exactly into the enclosure and the two top plates are cut in dimensions 150 x 215 mm to fit the motherboard. When mounting the motherboard it is important to align it to the edge to make room for the RJ-45 connections. Get printable drawings of Top deck, middle deck and lower deck (A3).
The lower deck holds the power supply, hard disk drive and the PCB The middle deck holds the router The top deck holds the motherboard and attached CAN adaptor.
Wiring
A splitter PCB is needed between the four serial connectors and the J18 connector on the motherboard. This can be done with the big and clumsy PCB that is delivered with the motherboard or with this nice and small PCB.
| COM1 | COM2 | COM3 | COM4 | |
| 1 | pink | blue | grey | grey |
| 2 | green | green | pink | blue |
| 3 | yellow | yellow | yellow | yellow |
| 4 | blue | pink | green | green |
| 5 | grey | grey | blue | pink |
| 6 | white | white | white | white |
| 7 | red | red | red | red |
| 8 | brown | brown | brown | brown |
| 9 | NC | NC | NC | NC |
| 10 | NC | NC | NC | NC |
Software
- Ubuntu 10.04
- ROS Electric
- Can4Linux
- Git 1.7.6.3
For information about the software installation please see the installation page.
Footnotes
1) 2
2) Hvordan regner du med at køre denne ground, mht. stelsløjfer? men stadig med mulighed for overførsel af store strømme? —morten
3) Her kommer vel samme problem —morten
4) 1
5) 3
6) 4
